| Number of analogue outputs |
2 None |
| Mains voltage |
480 V |
| Integrated breaking resistance |
False |
| Brake IGBT |
Brake IGBT installed |
| Internal communication module |
No communication module |
| Fuse current rating |
6A @ 650V DC |
| Input voltage rating |
480V AC, 3-phase, 60 Hz |
| AC input undervoltage trip |
280V AC @ 480V |
| Bus voltage, nom |
648V DC @ 480V |
| Bus undervoltage shutoff/fault |
305V DC @ 480V |
| Bus overvoltage trip |
810V DC @ 480V |
| Output voltage rating |
0…460V AC @ 480V AC, 1-phase |
| Circuit breaker current rating, max |
15A @ 480V AC, 3-phase |
| Motor circuit protector current rating, max |
7A @ 480V AC, 3-phase |
| Output current rating, continuous |
3.4A @ 650V DC |
| Output current rating, 1 min |
4.5A @ 650V DC |
| Output current rating, 3 sec |
6A @ 650V DC |
| Logic control ride-thru |
0.5 s minimum, 2 s typical |
| Brake resistor |
No internal brake resistor |
| Input current rating |
3.0A @ 650V DC |
| Documentation |
Manual |
| Carrier frequency |
2, 4, 8, and 10 kHz. Drive rating based on 4 kHz |
| Encoder quadrature |
90 degrees, ±27 degrees at 25 °C (77 °F) |
| AC input overvoltage trip |
570V AC @ 480V |
| Input power rating |
2.2 kVA @ 480V AC, 3-phase |
| Dual element time delay fuse current rating |
4…8A @ 480V AC, 3-phase |
| Non-time delay fuse current rating |
4…12A @ 480V AC, 3-phase |
| Digital input latency, typical |
9.2 ms @ stop signal for SVC motor control |
| Heat sink thermistor |
Monitored by microprocessor overtemp trip |
| Digital input latency |
9.2…16.0 ms @ start signal for SVC motor control |
| Drive to motor power ratio, max |
Recommended not greater than 2:1 ratio |
| Stop modes |
Multiple progmable stop modes including – RA, Coast, DC-brake, Fast brake, RA-to-hold and S-curve |
| Acceleration/deceleration |
Two independently progmable accel and decel times. Each time can be progmed from 0…3600 s in 0.1 s increments |
| Frequency accuracy |
Digital input: within ±0.01% of set output frequency |
| Analog input latency, typical |
6.4 ms @ speed signal for SVC motor control |
| Number of digital inputs |
6 None |
| Number of digital outputs |
3 None |
| Internal watts loss |
45 W @ 480V @ 2Hp normal duty (IP20, NEMA/UL Type 1) |
| Number of analogue inputs |
2 None |
| Motor voltage, nom |
460V @ 380…480V drive rating, 480V nominal line voltage |
| Human interface model |
LCD display full numeric keypad with progming keys |
| Supporting protocol for DeviceNet |
True |
| External watts loss |
31 W @ 480V @ 2Hp normal duty (IP20, NEMA/UL Type 1) |
| Max. output frequency |
420 Hz |
| Total watts loss |
76 W @ 480V @ 2Hp normal duty (IP20, NEMA/UL Type 1) |
| Line voltage, nom |
480V @ 380…480V drive rating, 460V nominal motor voltage |
| Supporting protocol for EtherNet/IP |
True |
| Mains frequency |
60 Hz |
| Actual short circuit rating |
Determined by AIC rating of installed fuse/circuit breaker |
| Internal EMC filtering |
With EMC filter with common mode choke |
| Custom drive/firmware |
No custom firmware |
| Feedback option |
No ftdback |
| Analog input latency |
4.8…12.4 ms @ speed signal for SVC motor control |
| Drive full power range |
460…528V @ 380…480V drive rating |
| Drive operating range |
342…528V @ 380…480V drive rating |
| Torque regulation |
Without ftdback: ±5 %, 600 rad/sec bandwidth |
| Enclosure type |
IP20/NEMA/UL Type 1 |
| Output current rating |
3.4 A, 2 Hp normal duty, 1.5 Hp heavy duty, frame 0 |
| Control options |
Vector control with 24V DC I/O |
| Drive overcurrent trip |
Instantaneous current limit: 220…300% of rated current (dependent on drive rating) |
| Efficiency |
97.5% at rated A, nominal line volts |
| Encoder supply |
12V @ 250mA. 12V @ 10mA minimum inputs isolated with differential transmitter, 250 kHz maximum |
| Speed control-speed regulation |
Without ftdback (Vector Control Mode): 0.1 % of base speed across 120:1 speed range, 120:1 operating range, 50 rad/sec bandwidth |
| Current limit capability |
Proactive current limit progmable from 20…160% of rated output current, Independently progmable proportional and integral gain |
| Selectable motor control |
Sensorless vector with full tuning. Standards V/Hz with full custom capability and vector control |
| Frequency control-speed regulation |
With slip compensation (Volts per Hz mode): 0.5% of base speed across 40:1 speed range, 40:1 operating range, 10 rad/sec bandwidth |
| Input phases |
3-phase input provides full rating for all drives. 1-phase ops possible on certain drives and provides 50 % of rated current. Frames 0…6: drive can be supplied as 6 pulse or 18 pulse in an engineered package. |
| Control method |
Sine coded PWM with progmable carrier frequency, ratings apply to all drives, the drive can be supplied as 6 pulse or 18 pulse in an engineered solution |
| Encoder requirements |
Encoders must be line driver type, quadrature (dual channel) or pulse (single channel), 8…15V DC output (4…6V DC when jumpers are in 5V position), single-ended or differential and capable of supplying a min. of 10 mA per channel, maximum input frequen |
| Number of phases output |
3 None |
| Number of phases input |
3 None |
| Relative symmetric net voltage tolerance |
10 % |
| With control element |
True |
| Supporting protocol for LON |
True |
| Supporting protocol for TCP/IP |
True |
| Supporting protocol for PROFIBUS |
True |
| Supporting protocol for CAN |
True |
| Supporting protocol for Modbus |
True |
| Motor overload protection |
Frames 0…6 vector control: powerflex 700 drives with vector control, which is identified by a C or D in position 15 of the catalog number, provide class 10 motor overload protection according to NEC article 430 and motor overtemperature protection acco |
| Input frequency tolerance |
47 Hz |
| Encoder duty cycle |
50% ±10% |
| Displacement power factor (all drives) |
0.98 across speed range |
| Short circuit rating, max |
200000 A symmetrical |
| Output voltage range |
0 to rated motor voltage |
| Encoder type |
Incremental, dual channel |
| Power ride-thru |
15 ms at full load |
| Short circuit trip |
Phase-to-phase on drive output |
| Ground fault trip |
Phase-to-ground on drive output |
| Drive to motor power ratio, min |
Recommended not less than 1:2 ratio |
| Control logic noise immunity |
Showering arc transients upto 1500V peak |
| Line transients |
Up to 6000 volts peak per IEEE C62.41-1991 |
| Intermittent overload |
110% overload capability for up to 1 min, 150% overload capability for up to 3 s |
There are no reviews yet.