| Number of analogue outputs |
2 |
| Mains voltage |
650 V |
| Integrated breaking resistance |
No |
| Max. output voltage |
932 |
| Brake IGBT |
Without brake IGBT |
| Internal communication module |
ControlNet coaxial |
| Fuse current rating |
400A @ 650V DC, normal duty |
| Input voltage rating |
650V DC no precharge |
| Displacement power factor |
0.98 across speed range |
| Output current, continuous |
248A @ 650V DC, normal duty |
| Output current, 1 min |
273A @ 650V DC, normal duty |
| Output current, 3 sec |
372A @ 650V DC, normal duty |
| Logic control ride-thru |
0.25 s, drive not running |
| Brake resistor |
No internal brake resistor |
| Input current rating |
272A @ 650V DC, normal duty |
| Rated power rating |
200Hp @ 650V DC, normal duty |
| Documentation |
English documentation |
| Carrier frequency |
Drive rating: 4 kHz, settings: 2, 4, 6, 8, 10 kHz (6 kHz is for V/Hz ops only) |
| Electronic motor overload protection |
Class 10 motor overload protection according to NEC article 430 and motor over-temperature protection according to NEC article 430.126 (A)(2). UL 508C file E59272 |
| Heat sink thermistor |
Monitored by microprocessor overtemperature trip |
| Drive to motor power ratio, max |
The drive to motor rating cannot exceed a 2:1 ratio |
| Stop modes |
Multiple progmable stop modes including – RA, Coast, and Current Limit |
| Acceleration/deceleration |
Independently progmable accel and decel times adjustable from 0 to 6553.5 in 0.1 s increments |
| Number of digital inputs |
6 |
| Number of digital outputs |
2 |
| Number of analogue inputs |
3 |
| Human interface model |
LCD Display, full numeric keypad |
| Additional configuration |
Phase II control |
| Max. output frequency |
400 |
| Internal EMC filtering |
With EMC filter & common mode choke |
| Watt loss |
2115 W @ 650V DC @ 200Hp normal duty |
| Feedback option |
Safe off with s encoder |
| Torque regulation |
Torque regulation – without ftdback: ±5%, 600 rad/sec bandwidth |
| Enclosure type |
IP20/NEMA/UL Type 1 |
| Output current rating |
248 A, 200 Hp normal duty, 150 Hp heavy duty, frame 6 |
| Control options |
Phase II control, expanded cassette |
| Drive overcurrent trip |
Software current limit: 105% of motor rated to 200% of drive rated current |
| Efficiency |
97.5% at rated A, nominal line volts |
| Speed control |
Speed regulation – without ftdback: 0.1% of base speed across 120:1 speed range, 120:1 operating range, 50 rad/sec bandwidth |
| Current limit capability |
Independent motoring and regenerative power limits progmable to 800% of rated output current |
| Selectable motor control |
Field oriented control with and without a ftdback device and permanent magnet motor control |
| Input phases |
Six-pulse, 3-phase input provides full rating for all drives, single-phase ops provides 50% of rated current |
| Control method |
Induction motor and brushless motor: sine coded PWM with progmable carrier frequency, indirect self organized, field-oriented control, current-regulated, ratings apply to all drives, refer to the PowerFlex 700S Phase ll control reference manual, public |
| Number of phases output |
3 |
| Number of phases input |
3 |
| Relative symmetric net voltage tolerance |
10 |
| Input frequency, max |
400 |
| Output frequency range |
0 |
| DC bus undervoltage trip |
Adjustable |
| Output voltage range |
0 to rated motor voltage |
| Power ride-thru |
15 ms at full load |
| S-curve time |
Adjustable 0.5…4.0 s |
| Short circuit trip |
Phase-to-phase on drive output |
| Ground fault trip |
Phase-to-ground on drive output |
| Control logic noise immunity |
Showering arc transients upto 1500V peak |
| Line transients |
Up to 6000 volts peak per IEEE C62.41-1991 |
| Intermittent overload |
110% overload capability for up to 1 min, 150% overload capability for up to 3 s |
| Short circuit current, max |
Using recommended fuse or circuit breaker type: maximum short circuit current rating to match specified fuse/circuit breaker capability ≤200000 A |
| Encoder voltage supply |
5V DC or 12V DC 320 mA/channel, 5V DC minimum high state voltage state of 0.4V DC @ 12V DC minimum high state voltage of 7.0V DC, maximum low state voltage of 0.4V DC |
There are no reviews yet.